2 Part Epoxy Putty: Where a Stick Beats a Mixed Batch

2 Part Epoxy Putty: Where a Stick Beats a Mixed Batch

Boat Suppliers
Boat Suppliers

13 November 2026

2 part epoxy putty comes three ways, and the job decides which one you reach for: a kneadable stick for a plug or a stripped hole you need hard in an hour, a cartridge like Six10 for a structural bead with no measuring, or a mixed batch of thick epoxy for anything bigger than a fist. The spec that settles it is volume and working time. Under about 2 oz and under 20 minutes, the stick wins. A bead you can gun in a line, the cartridge wins. Fillets, gap fills and bedding jobs that take a pint or more, mix a batch.

What a 2 part epoxy putty stick actually is

A stick is resin and hardener extruded as two concentric colors, already loaded with filler so it holds shape. You cut a length, knead it until the color is uniform, and press it in. Most marine sticks give you 15 to 25 minutes to work and are hard enough to drill or tap in about an hour; read the wrapper for the exact numbers, because they vary by brand. The filler loading is what makes it stay put, and it is also why a stick has lower bond strength than a properly mixed liquid epoxy: you cannot wet out a surface with something the consistency of modeling clay. It is the right call where nothing else works: an emergency plug on a weeping thru-hull, packing a stripped screw hole so the fastener bites, or building up a chipped hatch corner you will sand in an hour.

Stick vs cartridge vs mixed batch

Kneadable stick Six10 cartridge Mixed thick epoxy
Mix method Knead by hand Static mixing tip, 2:1 metered Measure 1:1, stir
Working time 15 to 25 min (see wrapper) About 42 min at 72°F See the TDS; longer in a shallow tray
Sag on vertical None None, holds a bead None with a high-build formula
Wets out the surface Poorly Yes Yes
Practical volume Up to about 2 oz 190 ml (6.4 oz) per cartridge Pint to gallons
Tint to color No No Yes, liquid pigment
Best at Plugs, thread fill, chips Bedding hardware, fillets, tack beads Gap filling, coating, long fillets

The cartridge is the one that surprises people. Six10 is 105-based West System epoxy thickened to a gel and packaged so the coaxial tube meters resin and hardener through the static tip. You get a structural, non-sag bead with the bond strength of a mixed batch and the convenience of a stick. It cures to a solid in 5 to 6 hours at 72°F (22°C) and reaches full strength over the next few days, so it is not a one-hour fix. The mixing tip is one use; the cartridge is not, so cap it and fit a fresh tip next session.

Where each one earns its place

Reach for the stick

Any repair where the hole is small, the clock is short, and you cannot get the surface clean and dry enough to wet out anyway. A weeping fitting below the waterline (some sticks cure underwater; check the label), a stripped screw hole in a fiberglass deck, a cracked battery box corner. Knead for a full minute; streaks mean an uncured soft spot later.

Reach for the cartridge

Bedding a cleat or stanchion base on a cored deck, running a fillet along a bulkhead before tabbing, gluing a backing block, or tacking a stringer in place before the glass goes on. West System Six10 Thickened Epoxy Adhesive does these with zero cups and zero measuring, and the bead tools with a gloved finger. By the math, one 190 ml cartridge lays about 9 ft of 3/8 in bead or nearly 20 ft at 1/4 in; buy two for a full bulkhead.

Mix a batch

Anything over a cartridge's worth, anything that needs color, or anything where you are also coating. The Boat Suppliers Epoxy Resin Kit, Thick, 1:1 Bonding and Coating, with Hardener is a high-build, no-sag 1:1 formula that fills a gap or glues hardware without running down a transom face, and it starts at a 16 oz kit so you are not opening a gallon for a small job. For a fillet that will show, tint it: 1 oz of Carbon Black Liquid Colored Pigments in a quart hides a fillet against a black bilge, and Autumn from the same line is the rust red that disappears against mahogany. Stir pigment into the resin side until streak-free, then add hardener.

Over a quart, mix with a drill and the 16" Steel Power Mixer; the 16 in shaft reaches the bottom of a gallon can where hand stirring leaves hardener behind. Wear a P100 respirator with organic vapor cartridges, nitrile gloves, and eye protection when mixing and sanding any of the three.

What a putty cannot do

None of the three is a laminating resin. If the repair is structural over an area, a hole through a hull, a cracked stringer, a soft transom, the fix is glass wet out with a thin laminating epoxy, not putty. The Boat Suppliers Epoxy Resin Kit, Thin, Clear, with Hardener is the 2:1 slow-cure system for that work. Use the putty to fillet and fair around the laminate, not instead of it. None of the three bonds to polyethylene, polypropylene, or an oily surface either: wipe with solvent, sand to 80 grit, and wipe again before any of them touches the part.

Frequently asked questions

How long does 2 part epoxy putty take to harden?

A kneadable stick is typically workable for 15 to 25 minutes and hard enough to drill in about an hour, with full cure at 24 hours; the wrapper has the exact schedule. Six10 in a cartridge gives about 42 minutes of working time at 72°F and is solid in 5 to 6 hours. For a same-day fix, use the stick; for a bond that carries load, use the cartridge and wait overnight.

Is epoxy putty waterproof once cured?

Fully cured epoxy is waterproof, and a few sticks are formulated to cure while submerged for emergency plugs. The weak point is the bond, not the putty: a surface with slime or oil on it will let go. For anything that stays below the waterline, grind to clean laminate, dry it, and use Six10 or a mixed batch of thick epoxy, then give it a full 24 hours before launch.

Will epoxy putty stick to fiberglass?

Yes, if the gelcoat is sanded through to laminate with 80 grit and wiped with solvent first. A kneadable stick bonds well enough for a plug or a screw hole. For a cleat base, a bulkhead fillet, or anything that sees load, use Six10 or a mixed thick epoxy, because a liquid that wets the surface bonds several times better than a filler-loaded stick pressed against it.

How much does one Six10 cartridge cover?

A cartridge holds 190 ml (6.4 oz) of mixed adhesive. That is about 9 ft of 3/8 in bead or close to 20 ft at 1/4 in, which covers two cleat bases with backing blocks or one side of a 4 ft bulkhead fillet. Plan on two cartridges for a bulkhead both sides, and buy spare mixing tips, since each tip is good for one session.

Can you sand and paint over epoxy putty?

Yes, after full cure. Wash the surface with water to lift amine blush, then sand with 80 grit and finish at 120 before primer. Sticks sand hard and fast; Six10 and a mixed thick epoxy sand about like a fairing compound. If you want the repair to vanish under a colored finish, tint a mixed batch with 1 oz of liquid pigment per quart instead of trying to hide a gray stick.

What You Need For This Job

Back to blog