Vacuum Bagging Layers Chart
The layers of a vacuum bag in the order they go down, what each one does, and the width and spec of the one we sell for it.
- Layers in order
- What each layer does
- Widths and specs
- Kit contents
Vacuum Bagging Layers In Order
Working up from the part. Layer 1 goes on the wet laminate and the bag goes on last.
| Layer | What It Does | Product |
|---|---|---|
| 1. Peel ply | Goes directly on the laminate. Comes off after cure and leaves a textured surface you can bond to. | Peel Ply Release Fabric |
| 2. Perforated release film | Lets excess resin bleed through to the breather, and still peels off the cured part. | Perforated Release Film |
| 3. Breather | Gives air a path to the port from every corner of the bag, and absorbs the resin that bleeds through. | 4oz Breather Cloth, or 7oz Breather Cloth for thick wet layups |
| 4. Bagging film | The outer bag. Stretches into inside corners and over deep draws. | Nylon Bagging Film |
| 5. Sealant tape | Seals the bagging film to the mold flange and stays tacky through the cure. | Vacuum Bagging Sealant Tape |
| 6. Bag connector | Gets vacuum through the bag. Sits on the breather, never straight on the laminate. | Aluminum Vacuum Bag Connector |
The release film is the layer that meters resin bleed. Our two smaller kits run peel ply, breather and bag without it; the large kit adds it.
Widths, Specs And Coverage Per Yard
What to check before you cut: the width has to clear the part with room for pleats.
| Material | Width | Spec | Sq Ft Per Yard |
|---|---|---|---|
| Peel ply | 60 in | Leaves a medium texture, bondable without sanding | 15 |
| Perforated release film | 60 in | Blue, perforated on 1/2 in centers | 15 |
| 4 oz breather cloth | 60 in | Polyester, rated to 400 F | 15 |
| 7 oz breather cloth | 60 in | Polyester, holds more resin than 4 oz | 15 |
| Nylon bagging film | 110 in | Opens flat to 110 in from a 55 in fold | 27.5 |
| Sealant tape | 1/2 in | 1/8 in thick, 25 ft per roll | n/a |
| Aluminum bag connector | n/a | 1/4 in male NPT stem, reusable | n/a |
Square feet per yard = width in inches x 3 / 12.
What Is In Each Vacuum Bagging Kit
The same layers, packed three ways.
| Kit | Bagging Film | Peel Ply | Breather | Release Film | Sealant Tape | Connector And Hose |
|---|---|---|---|---|---|---|
| Vacuum Bagging Consumables Kit | 2 yd | 2 yd | 2 yd | None | 1 roll | Not included |
| Vacuum Bagging Starter Kit | 3 yd | 3 yd | 3 yd | None | 2 rolls | Aluminum connector, 10 ft hose, fittings and clamps |
| Vacuum Bagging Kit Large | 5 yd | 5 yd | 5 yd | 2 yd | 2 rolls | Not included |
Film is 110 in wide, peel ply, breather and release film 60 in, and each roll of tape is 25 ft. The large kit also has a roll of flash tape. No kit includes a pump.
How To Lay Up The Bag
Peel ply goes straight onto the wet laminate. Smooth the release film flat over it, since any fold or wrinkle presses into the surface of the cured part. Breather goes over that, then the bagging film, sealed to the mold flange with one bead of sealant tape.
Leave slack in the bag. A bag pulled tight bridges the corners, and that is where parts go dry. At corners, pleat the film into the tape instead of stretching it.
Set the connector over breather so the vacuum pulls across the whole bag instead of collapsing on one spot. Pull vacuum, walk the bag down into every corner by hand, then hunt leaks before the resin kicks.
Vacuum Bagging Layers Chart FAQ
What order do vacuum bagging layers go in?
Working up from the part: laminate, peel ply, perforated release film, breather, then the bagging film sealed to the mold with sealant tape. The connector sits on top of the breather.
Does peel ply go under or over the release film?
Under. Peel ply goes directly on the laminate, with the release film and breather over it.
What does breather cloth do in a vacuum bag?
It gives air a path to the port from every corner of the part, and it absorbs the resin that bleeds out. Without it the film seals against the laminate and nothing is pulled through the part.
When do I need 7 oz breather instead of 4 oz?
On heavy laminates, high resin content, or any bag where a 4 oz breather comes out soaked. 4 oz is the general purpose weight.
How wide is vacuum bagging film?
Our nylon bagging film is 110 in wide opened flat. It comes folded to 55 in on the roll, and one yard covers 27.5 sq ft.
How much sealant tape do I need?
One bead around the mold flange. Each roll is 25 ft, so measure the perimeter of the bag and add for pleats and repairs.
Is a pump included in the vacuum bagging kits?
No. The kits are the consumables. The Starter Kit also has an aluminum bag connector, 10 ft of hose, fittings and clamps.