Sea Hawk Biocop TF Bottom Paint

Sea Hawk Biocop TF Bottom Paint

Sea Hawk's Biocop TF Bottom Paint is a multi-season, self-polishing antifouling paint that provides maximum fouling protection. Bicop TF was developed as an alternative to tin-based antifouling paints to stand up to the harshest marine environments. The new Dual biocide technology and groundbreaking polymer binder system, PL3, produces a biocide that leaves no harmful effects on the environment. Safe for salt or fresh water on boats of all sizes, Biocop TF is a top performer among bottom paints.

How to Apply Sea Hawk Biocop TF Bottom Paint

Sea Hawk Biocop TF Bottom Paint is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap 3/8” roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 10% using water. Biocop TF has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.

Surface Preparation and Application

Previously Painted Surfaces

• Known Compatibility of existing antifoulant
• Power wash to remove any loose paint or other contaminants.
• Scuff sand with 80 grit sandpaper, remove all residue and let dry.
• Apply minimum 2 coats of Biocop TF. Allow 3-6 hours between coats and a minimum overnight dry.
• Unknown Compatibility of existing antifoulant
• Power wash to remove any loose paint or other contaminants.
• Scuff sand with 80 grit sandpaper, remove all residue and let dry.
• Apply 1 coat of 1277 Barrier coat primer or 1283 Island Primer
• Apply minimum of two coats of Biocop TF. Allow 3-6 hours between coats and a minimum overnight dry.
• Poor condition of existing antifoulant
• If previous coating is cracking, peeling, or flaking strip the antifoulant with stripper, sanding, or commercial blasting.
• Once stripped refer to the Bare Fiberglass Application Guidelines.

Bare Fiberglass

• To prepare the surface it is important to remove all contaminants first. Scrub the surface with detergent soap and a stiff brush.
• Using either S-80 Wax N’ Grease Killer or S-90 De-Wax Etch & Cleaner scrub the surface and rinse thoroughly.
• Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner
• Once cleaned and sanded, seal the surface with 2-3 coats of Tuff Stuff. Apply the second coat once the first has a tacky feel.
• Apply minimum of two coats of Biocop TF. Allow 3-6 hours between coats and a minimum

Sanding Method:

• Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & Cleaner
• Apply minimum of two coats of Biocop TF. Allow 3-6 hours between coats and a minimum overnight dry.

Non-Sanding Method:

• Apply one thin coat of Sea Hawk 1266 no more than .3-.5 mils wet film thickness and allow to dry for 1 hour.
• Apply minimum of two coats of Biocop TF. Allow 3-6 hours between coats and a minimum overnight dry.

Bare Wood

• Clean the surface and ensure it is dry and free of contaminants.
• Sand to a uniformly frosty, dull looking surface with 80-100 grit sandpaper.
• Apply two coats of Biocop TF. Apply first coat thinned 20% and let dry overnight.
• Apply two more coats allowing 3-6 hours between coats and a minimum overnight dry.

Steel/Aluminum Hulls

• Sandblast to near white or white metal SSPC-SP-10 or equivalent. Remove residue by brush or compressed air.

Copper Based Antifoulant Application

• Apply two coats of S-76 Primer, the first coat applied within 1 hour of sanding. Allow the first coat to dry to a tacky feel then apply second coat.
• Seal the surface by using 3-4 coats of Tuff Stuff. Apply the first coat within 8 hours of applying the last coat of S-76.
• Apply minimum of two coats of Biocop TF, allow 3-6 hours between coats.

Copper-Free Antifouling Application for Aluminum Only

Above information sourced from Sea Hawk Bottom Paint Application Instructions

Click Here to Download Sea Hawk Biocop TF Application Guide

Click Here to Download Sea Hawk Bottom Paint Compatibility Chart

Frequently Asked Questions

What is Sea Hawk Biocop TF Bottom Paint used for?

Sea Hawk Biocop TF Bottom Paint is a multi-season, self-polishing antifouling paint designed to provide fouling protection in marine environments. It can be used in both fresh and salt water and is approved for vessels of all sizes. Its dual-biocide PL3 release technology is designed as an alternative to tin-based antifouling paints.

Can Sea Hawk Biocop TF Bottom Paint be used in fresh and salt water?

Yes. Sea Hawk Biocop TF Bottom Paint is formulated for use in both fresh and salt water. The product description states that it provides multi-season performance and is approved for vessels of all sizes, making it suitable for the marine applications specified by the manufacturer.

How many coats of Sea Hawk Biocop TF Bottom Paint are recommended?

A minimum of two coats of Biocop TF is recommended for the application procedures provided. Allow 3-6 hours between coats and a minimum overnight dry. When applying over bare fiberglass, the surface should first be prepared and sealed according to the specified fiberglass preparation procedure.

How should Sea Hawk Biocop TF Bottom Paint be applied?

Biocop TF can be applied by brush, roller, or airless sprayer. When rolling, use a high-quality short-nap roller with a maximum 3/8-inch nap and apply thin coats. For the smoothest finish, the product can be thinned approximately 10% as specified in the application instructions.

How should previously painted surfaces be prepared for Sea Hawk Biocop TF?

For a known-compatible antifouling coating, power wash to remove loose paint and contaminants, then scuff sand with 80-grit sandpaper, remove residue, and allow the surface to dry. If compatibility is unknown, the instructions call for a barrier coat or primer before applying a minimum of two coats of Biocop TF.

What are the coverage and application specifications for Sea Hawk Biocop TF Bottom Paint?

Sea Hawk Biocop TF has a stated coverage of 320 square feet, with a wet film thickness of 5.0 mils and dry film thickness of 2.2 mils. Apply between 50°F and 95°F. The finish is semi-gloss, and the specified roller thickness is a maximum 3/8-inch nap.